TERMS & CONDITIONS

Supplier Terms & Conditions Agreement

General: As a supplier to Aircraft Welding Inc., it is understood that when accepting our purchase orders, your organization agrees to meet the following stipulations / AS9100 requirements whenever Aircraft Welding Inc. Purchase Orders have an “A” prefix present on the associated Job Number (or contains some similar aerospace/AS9100 reference). An example of this would be Job: A10123. These requirements are, therefore, to be considered as terms and conditions to all aerospace purchases:

1. Where required on the Aircraft Welding Inc. Purchase Orders, its suppliers must use Aircraft Welding Inc.’s customer-approved special process sources.

2. Aircraft Welding Inc. is to be contacted (by the supplier) in the event of nonconforming
product/material. Arrangements for the approval of supplier nonconforming product/material must be as directed by an Aircraft Welding Inc.’s representative.

3. Furthermore, the supplier is required to notify Aircraft Welding Inc. of any changes to a product and/or process and to obtain approval from an authorized Aircraft Welding Inc. representative when applicable.

4. Aircraft Welding Inc., their customers, and regulatory authorities retain the right of access to all supplier facilities involved in the aerospace order and to all applicable records.

5. The AS9100 standard requires that all applicable customer/regulatory/AS9100 requirements for the supplier to flow-down to sub-tier suppliers (includes requirements in the purchasing documents and key characteristics where required). However, Aircraft Welding Inc. does not allow its aerospace suppliers to subcontract any product or process to a sub-tier supplier without Aircraft Welding Inc. expressed written consent.

6. Aircraft Welding Inc. performs inspection activities to ensure that purchased product meets purchase requirements. They may include:

1. a. Receiving inspections (of supplier products / services / documents) may be / are performed by a designated employee. Aircraft Welding Inc. verifies the authenticity of the appropriate certificate of conformity, material certificates, etc. and other accompanying documentation by review and comparison (as is appropriate) to the drawing and/or industry specifications or by other means. When necessary, Aircraft Welding Inc. may inspect or audit at the supplier’s facility.

2. b. Furthermore, products are inspected to ensure they meet requirements (dimensions, etc.) and the results are recorded (as appropriate). All special processes (anodizing, heat treat etc.) where the compliance cannot be verified by inspections will require a Certificate of Conformity.

7. When appropriate, Aircraft Welding Inc. may delegate the inspection authority to one of its approved suppliers. Aircraft Welding Inc. will communicate the inspection requirements (including approved monitoring and measurement equipment/methods) and Aircraft Welding Inc. will maintain a record of those approved to carry out such inspections.

8. When Aircraft Welding Inc. or its customer intends to perform verification at the supplier’s premises; Aircraft Welding Inc. will first state the intended verification arrangements and the method of product release. This information will be communicated on the Aircraft Welding Inc. Purchase Order or via another acceptable purchasing arrangement.

9. Where specified in the contract, the Aircraft Welding Inc.’s customer or customer’s representative will be afforded the right to verify at the supplier’s premises and Aircraft Welding Inc.’s premises that subcontracted product conforms to specified requirements. Verification by the customer is not used by Aircraft Welding Inc. as evidence of effective control of quality by the supplier and shall not absolve Aircraft Welding Inc. or its supplier of the responsibility to provide acceptable product, nor shall it preclude subsequent rejection by the customer. 

10. To prevent the purchase of counterfeit or suspect/unapproved products and to ensure product identification and traceability (and for other reasons), Aircraft Welding Inc. will institute controls that include the requirement of Material Certificates, Certificates of Conformity, and/or other supporting documentation from its suppliers as is appropriate. These requirements may be specified on Aircraft Welding Inc.’s Purchase Order or may otherwise be communicated to the supplier. 

11. Records are available for review by customers and regulatory authorities in accordance with contract or regulatory requirements.

12. Aircraft Welding Inc. expects 100% on time delivery. If the agreed upon delivery cannot be met, the appropriate Aircraft Welding representative must be notified in advance. If Aircraft Welding Inc. annual supplier evaluation identifies a supplier with an on-time delivery rate of 95% or less a corrective action can be issued.

13. Aircraft Welding Inc. requires that products provided by it’s Approved Suppliers be correct and free of defect per the supplied Purchase Order. If Aircraft Welding Inc. annual supplier evaluation identifies a supplier with a scrap/rework rate that exceeds 10% of their Aircraft Welding work orders; a corrective action can be issued.

14. Aircraft Welding Inc. may also require specific actions where timely and/or effective corrective actions to a supplier issue(s) are not achieved. These actions may include but are not limited to any or all of the following: withholding payment until the issue is resolved, removal of the supplier from Aircraft Welding Inc.’s Approved Supplier List, and/or legal action.

QC-03.04FM REV A